Why are pot fillers exclusively plumbed with a cold water line?

Pot fillers are strictly engineered for cold water rough-ins for three critical plumbing and culinary reasons: 1) Boiling cooking water must always start cold to avoid dissolved minerals, heavy metal sediment, and scale that accumulate inside residential water heater storage tanks; 2) Stoves generate intense ambient heat, and sitting hot water in stagnant pipes rapidly cools anyway, wasting hot water energy; 3) Cold water line pressure is significantly more stable, delivering an unrestricted 4.0 GPM flow rate for rapid kettle and Dutch oven fills.

What is the exact rough-in height for an unlacquered brass pot filler?

Standard architectural guideline is 12 to 14 inches above the stovetop burner grates, measured to the center of the 1/2" NPT drop-ear supply elbow. To calculate your home’s exact rough-in: measure your tallest kitchen stockpot or canning kettle (e.g. 11 inches) and add 2.5 to 3 inches of clearance. This allows you to effortlessly swing the 24-inch articulating arm over the pot rim while avoiding heat splatter and steam condensation.

Why does a commercial pot filler require two independent shut-off valves?

Unlike a standard sink faucet situated over a drainage basin, a pot filler is suspended directly over an expensive gas cooktop or induction range with zero floor drain. Commercial plumbing codes require dual shut-off valves (a primary wall valve and a secondary spout tip valve) so that if one valve ever experiences pressure fluctuations or wear, the second valve provides a foolproof mechanical backup against water damage or boiling stove emergencies.

Will heat from high-BTU gas burners damage unlacquered brass?

No. 100% solid virgin architectural brass possesses an exceptionally high melting point of 1,710°F (932°C) and contains zero synthetic lacquers or clear coats to bubble, scorch, or peel. When exposed to stove warmth and cooking steam, raw unlacquered brass simply accelerates its natural living patina, developing deep amber, honey, and antique bronze tones characteristic of historic European estate kitchens.

How do I clean cooking grease and steam splatters off raw brass?

For weekly care, wipe down with a soft microfiber cloth dampened in warm soapy water (Dawn dish soap works wonderfully to cut kitchen grease). To preserve the aged patina, never use harsh chemical oven degreasers. If you wish to restore the bright golden luster, a 60-second polish with Cape Cod metal polishing cloth or gentle brass cream dissolves cooking oils and restores original mirror brilliance immediately.

Does this pot filler fit standard American residential plumbing?

Yes. Every Medina Brass pot filler is engineered with standard American 1/2-inch NPT (National Pipe Taper) threads. Your plumber simply installs a standard 1/2" female brass drop-ear elbow secured tightly to a 2x4 wood blocking stud behind the drywall or tile backerboard.

Can a pot filler be mounted directly into drywall or is wood blocking required?

A pot filler should NEVER be mounted into unsupported drywall or hollow tile. Because our 24-inch dual articulating pot filler is cast from solid architectural brass and weighs 5.2 lbs, swinging the fully extended arm creates dynamic leverage. Your plumbing contractor must install a horizontal 2x4 solid wood backing block fastened between wall studs to anchor the 1/2" drop-ear elbow rigidly.

What is the difference between Medina Brass and Kingston Brass pot fillers?

Kingston Brass manufactures mass-market fixtures typically cast from thin zinc alloy ("pot metal") coated with a decorative electroplated brass lacquer. Over a hot stove, the heat causes the thin lacquer coating to peel, pit, and blister. Medina Brass fixtures are hand-cast from 100% solid virgin 65/35 architectural brass with no artificial lacquers, meaning the metal is solid all the way through and patinas authentically for generations.

Pillar Architectural MonographArchitectural Plumbing Specs10 Min Read

The Architectural Guide to Unlacquered Brass Pot Fillers: Rough-In Heights, Metallurgy & 4-Way Brand Comparison

An unlacquered brass pot filler represents the ultimate intersection of culinary utility and old-world foundry craft. Here is the definitive architectural specification manual detailing exact rough-in heights, dual ceramic shutoff valve engineering, cold-water plumbing science, and a rigorous side-by-side comparison of Medina Brass vs. Kingston Brass, deVOL, and Waterstone.

Karim BenaliFoundry Metallurgy Lead • Marrakech Medina

Certified 100% Solid Architectural Brass (CuZn37) • US 1/2" NPT Verified

Handcrafted Unlacquered Brass Wall-Mount Pot Filler - Front View

Marrakech Foundry Flagship

Artisan Direct • No Showroom Markup

Handcrafted Unlacquered Brass Wall-Mount Pot Filler Faucet

Dual-jointed 24-inch articulating swing arm stove faucet cast from solid binary 65/35 architectural brass in Marrakech. Includes dual quarter-turn ceramic valves and standard 1/2" NPT American plumbing threads.

$389.00$460.00 USDSave 20% vs Retail Showrooms

100% Solid Living Brass

Standard 1/2" NPT Pipe Threads

Dual Ceramic Disc Valves

Complimentary Air Dispatch

View Full Product Detail Page

In Stock • Ships in 24h via Tracked Express Air

Foundry Coordination

Complementary Kitchen Brass Fixtures

Explore Kitchen Collection

Kitchen Fixtures

Unlacquered Solid Brass Gooseneck Kitchen Faucet — Single Lever Culinary

$248.00View Specs →

Kitchen Fixtures

Unlacquered Brass Countertop Built-in Soap Dispenser

$149.00View Specs →

Kitchen Fixtures

Solid Brass 3.5" Kitchen Sink Strainer Basket Assembly

$85.00View Specs →

Kitchen Fixtures & Sinks

Hand-Hammered Moroccan Solid Brass Bar & Prep Sink

$425.00View Specs →

Engineering & Metallurgy Audit

The 4-Way Pot Filler Benchmark

Comparing pure monolithic solid brass against mass-market plated zinc and European luxury showroom imports.

Specification	Medina Brass (Atelier)	Kingston Brass	deVOL Kitchens	Waterstone
Base Metallurgy & Alloy Integritymetallurgy	100% Solid Virgin Architectural Brass (65/35 Cu/Zn, 8.53 g/cm³ density, zero pot metal)	Die-cast zinc alloy core with thin electroplated brass skin	High-grade European machined solid brass billet	American precision CNC-turned solid brass bar stock
Living Finish & Patina Longevitymetallurgy	Raw Unlacquered Living Brass — naturally self-healing antique caramel & honey bronze patina	Clear polyurethane protective lacquer — permanently clouds & peels under heat	Raw Living Brass — exceptional English heirloom aging	Living Brass option available (requires special custom lead time)
Dual Shut-Off Safety Valvesvalves	Dual 1/4-Turn Commercial Ceramic Disc Cartridges (tested to 500,000 leak-free cycles)	Standard ceramic cartridge (lower pressure threshold)	Precision European quarter-turn ceramic cartridges	Proprietary heavy-duty commercial ceramic disc valving
Pipe Thread Standards (US Plumbing)valves	Standard US 1/2" NPT Female / Male Pipe Thread (zero adapters needed)	Standard US 1/2" NPT	British Standard Pipe (BSPP/G-thread) — requires US NPT conversion adapters	Standard US 1/2" NPT
Direct Retail Price Pointprice	$389.00 USD (Direct Marrakech Atelier — no multi-tier retail markup)	$220.00 – $340.00 USD (Budget mass production with plated finish)	$1,150.00 – $1,600.00 USD (Imported UK bespoke markups)	$1,650.00 – $2,400.00 USD (Extreme luxury designer retail markup)
Fulfillment & US Lead Timesprice	Complimentary Tracked Air Dispatch (Delivered direct in 3–5 business days)	Warehouse stock (2–5 business days)	Custom made-to-order from UK (8 to 16 week lead time)	Custom built-to-order (6 to 10 week lead time)

The Metallurgy Truth

Why Plated Pot Fillers Fail Over Heat, and Why Solid Living Brass Endures

Gas range burners produce between 15,000 and 25,000 BTUs of radiant heat. Plated fixtures coated with clear acrylic lacquers (such as budget Kingston Brass reproductions) inevitably undergo micro-cracking and thermal delamination as the underlying zinc core expands at a different rate than the lacquer coating. Because Medina Brass fixtures are hand-cast from monolithic 100% solid architectural brass without chemical clear coats, there is zero coating to peel, pit, or blister. The living surface breathes and deepens into a magnificent antique amber patina that becomes richer each time you cook.

Technical Monograph

Architectural Rough-In Sizing & Plumbing Science

Installing an articulating pot filler requires careful alignment of wall framing, rough-in height, and cold-water supply plumbing.

✦ 12"–14" Rough-In Height

Above Range Burners

Standard rough-in center is 12 to 14 inches above the stovetop grates. Measure your tallest stockpot or Dutch oven and ensure at least 2.5 inches of clearance over the pot rim.

✦ Solid Stud Backing

2x4 Wood Reinforcement

Because our 24-inch dual articulating pot filler weighs 5.6 lbs of solid brass, a horizontal 2x4 wood blocking brace must be secured between wall studs to anchor the 1/2" drop-ear elbow rigidly.

✦ Cold Water Only

Single Supply Line

Plumbed exclusively to cold potable water. Cooking water should always begin cold to avoid sediment and scale from water heaters, and cold water pressure ensures 4.0 GPM high-flow fill speeds.

Plumbing & Contractor FAQs

Frequently Asked Pot Filler Questions

Clear technical answers covering water temperature codes, rough-in standards, dual valve mechanics, and living finish preservation.